ram ( 8-bit) rom ( 8-bit) 64 k type MN101C75D(under development) package 2 k lqfp080-p-1414a *lead-free MN101C75D minimum instruction execution time 0.125 s (at 3.0 v to 3.6 v, 8 mhz, non-use of usb) 62.5 s (at 3.0 v to 3.6 v, 32 khz, non-use of usb) interrupts ? reset watchdog external 0 external 1 external 2 external 4 (key interrupt dedicated) timer 0 timer 1 timer 2 timer 3 timer 6 time base timer 7 (2 systems) timer 8 (2 systems) serial 0 (2 systems) serial 2 a/d conversion f inish automatic transfer finish usb interrupts timer counter timer counter 0 : 8-bit 1 (square-wave/8-bit pwm output, event count, generation of remote control carrier, simple pulse width measurement) (square-wave/pwm output to large current terminal p50 possible) clock source 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 0 timer counter 1 : 8-bit 1 (square-wave output, event count, synchronous output event) clock source 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 1 timer counter 0, 1 can be cascade-connected. timer counter 2 : 8-bit 1 (square-wave output, additional pulse type 10-bit pwm output, event count, synchronous output event, simple pulse width measurement) (square-wave/pwm output to large current terminal p52 possible) clock source 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 2 mad00037cem
usb functions conforms to usb1.1. usb transceiver built-in full-speed (12 mbps) supported. 5 end points (fifo built-in independently) fifo size (ep0, 1, 2, 3, 4): 16, 128, 128, 128, 128 bytes ep0 control transfer in/out (two ways) ep1 to ep4 interrupt/bulk/isochronous transfer supported. settable to in or out. double buffering function supported. when the maxp size is set to a half or less of the maxfifo size for each ep, the double buffering function is made valid automatically. timer counter 3 : 8-bit 1 (square-wave output, event count, generation of remote control carrier, serial 0 baud rate timer) clock source 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency; external clock input interrupt source coincidence with compare register 3 timer counter 2, 3 can be cascade-connected. timer counter 6 : 8-bit freerun timer clock source 1/1 of system clock frequency; 1/1, 1/128, 1/8192 of osc oscillation clock frequency; 1/1, 1/128, 1/8192 of xi oscillation clock frequency interrupt source coincidence with compare register 6 timer counter 7 : 16-bit 1 (square-wave output, 16-bit pwm output (cycle / duty continuous variable), event count, synchronous output evevt, pulse width measurement, input capture) (square-wave/pwm output to large current terminal p51 possible) clock source 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of osc oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency interrupt source coincidence with compare register 7 (2 lines) MN101C75D mad00037cem timer counter (continue)
timer counter (continue) timer counter 8: 16 bit 1 (square-wave/16-bit pwm output [duty continuous variable], event count, pulse width measurement, input capture) (square-wave/pwm output to large current terminal p53 possible) clock source 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of osc oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency interrupt source coincidence with compare register 8 (2 lines) timer counters 7, 8 can be cascade-connected. (square-wave output, pwm, input capture, pulse width measurement is possible as a 32-bit timer.) time base timer (one-minute count setting) clock source 1/1 of osc oscillation clock frequency; 1/1 of xi oscillation clock frequency interrupt source 1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768, of clock source frequency watchdog timer interrupt source 1/65536, 1/262144, 1/1048576 of system clock frequency serial interface serial 0 : synchronous type/uart (full-duplex) 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 1 or 2; 1/2, 1/4, 1/16, 1/64 of osc oscillation clock frequency serial 2 : synchronous type/single-master i 2 c 1 clock source 1/2, 1/4 of system clock frequency; pulse output of timer counter 2 or 3; 1/2, 1/4, 1/16, 1/32 of osc oscillation clock frequency i/o pins 62 common use specified pull-up resistor available input/output selectable (bit unit) i/o a/d inputs 10-bit 12-ch. (with s/h) lcd 32 segments 4 commons (static, 1/2, 1/3, or 1/4 duty) lcd power supply separated from vdd (usable if vdd vlcd 3.6 v) lcd power step-up circuit contained (3/2, 2 and 3 times) lcd power shunt resistance contained special ports usb ports (d+, d-), buzzer output, remote control carrier signal output, high-current drive port electrical characteristics supply current limit symbol condition min typ max unit parameter idd1 fosc = 8 mhz, vdd = 3.3 v (non-use of usb) t.b.d. ma idd2 fosc = 6 mhz, vdd = 3.3 v (use of usb) t.b.d. ma idd3 fx = 32 khz, vdd = 3.3 v t.b.d. a idd4 fx = 32 khz, vdd = 3.3 v, ta = 25c t.b.d. a idd5 fx = 32 khz, vdd = 3.3 v, ta = ? 40 c to +85c t.b.d. a idd6 vdd = 3.3 v, ta = 25 ct.b.d. a idd7 vdd = 3.3 v, ta = ? 40c to +85 ct.b.d.ma operating supply current mad00037cem supply current at halt supply current at stop
pin assignment (at single chip mode) lqfp080-p-1414a * lead-free 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 v lc3 /p34 v lc2 v lc1 c2 tm0o/led0/p50/c1 tm7o/led1/p51 tm2o/led2/p52 tm8o/led3/p53 v ss osc2 osc1 sstrt xi xo soscmd v dd nrst/p27 v ref+ an0/pa0 an1/pa1 tm8io/p15 tm7io/p14 tm3io/p13 tm2io/p12 tm1io/p11 rmout/tm0io/p10 sbt2/an11/p07 sbi2/an10/p06 sbo2/an9/p05 sbt0a/an8/p04 rxda/sbi0a/an7/p03 txda/sbo0a/an6/p02 nbuzzera/an5/p01 buzzera/an4/p00 av ss d- d+ av dd an3/pa3 an2/pa2 p67/seg16 p66/seg17 p65/seg18 p64/seg19/sbt0b p63/seg20/sbi0b/rxdb p62/seg21/sbo0b/txdb p61/seg22/nbuzzerb p60/seg23/buzzerb p47/key7/seg24/sdo7 p46/key6/seg25/sdo6 p45/key5/seg26/sdo5 p44/key4/seg27/sdo4 p43/key3/seg28/sdo3 p42/key2/seg29/sdo2 p41/key1/seg30/sdo1 p40/key0/seg31/sdo0/sysclk v dd p22/irq2 p21/irq1/acz p20/irq0 p70/seg15 p71/seg14 p72/seg13 p73/seg12 p74/seg11 p75/seg10 p76/seg9 p77/seg8 p80/seg7 p81/seg6 p82/seg5 p83/seg4 p84/seg3 p85/seg2 p86/seg1 p87/seg0 p30/com0 p31/com1 p32/com2 p33/com3 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 MN101C75D type mn101cf75d (under development) rom ( 8-bit) 128 k ram ( 8-bit) 10 k minimum instruction execution time 0.125 s (at 3.0 v to 3.6 v, 8 mhz) 0.167 s (at 3.0 v to 3.6 v, 6 mhz) 0.25 s (at 1.8 v to 3.6 v, 4 mhz) 62.5 s (at 1.8 v to 3.6 v, 32 khz) package lqfp080-p-1414a *lead-free support tool flash memory built-in type in-circuit emulator px-ice101c / d + px-prb101c75-lqfp080-p-1414a-m (under development) MN101C75D mad00037cem
request for your special attention and precautions in using the technical information and semiconductors described in this material (1) an export permit needs to be obtained from the competent authorities of the japanese government if any of the products or technical information described in this material and controlled under the "foreign exchange and foreign trade law" is to be exported or taken out of japan. (2) the technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. it neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) we are not liable for the infringement of rights owned by a third party arising out of the use of the technical information as described in this material. (4) the products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are re- quired, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (5) the products and product specifications described in this material are subject to change without notice for modification and/or improvement. at the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (6) when designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. otherwise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physi- cal injury, fire, social damages, for example, by using the products. (7) when using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) this material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of matsushita electric industrial co., ltd. 2003 sep
|
